Garage, home and business floors from Brooksville to Tampa. Flake runs $4 to $12 a sq ft, and a typical job takes 2 to 3 days.Garage, home and business floors from Brooksville to Tampa.
A typical job takes 2 to 3 days. Here is every layer, shown for a flake floor.
01
Slab
Your bare concrete, with its stains and cracks.
02
Grind
Diamond tooling opens up the surface so the coating can bite into it. A dust extractor on the grinder catches the dust. This step decides how long the floor holds.
03
Crack repair
Cracks and chips get opened up, filled and ground flush, so they don't show through later.
04
Base coat
Walls and steps are taped off. Then the colored base coat goes down over the whole slab, edge to edge.
05
Flake
Flake goes into the base coat while it's still wet, broadcast until the floor is covered. Once it sets, the loose flake is scraped off.
06
Topcoat
A clear coat locks the flake in and gives the floor its gloss and its wear layer.
2 to 3 days
The man behind the floors
Meet the owner
Mel Wright spent 10 years in home improvement. In 2026 he left that job and started Dungeon Epoxy Designs. Going from home improvement into epoxy floors, he says, was a natural move.
Every request comes straight to us. We call you back as soon as we can, then come out to look at the slab.
On the system we agreed to install, as long as you follow the care instructions.
Covers system failure
Covers prep failure
Holds when you follow the care instructions
Where we work
Based in Brooksville
We work in five counties: Hernando, Pasco, Hillsborough, Pinellas and Polk. Home base is Brooksville. Spring Hill and Weeki Wachee are down the road, and we drive south to Tampa and the Pinellas coast and east into Polk.
We also take larger jobs in the Orlando area, by quote.
A typical job takes 2 to 3 days. We'll tell you what to expect for your floor once we've seen it.
Floors carry a 5 to 10-year limited warranty, depending on maintenance and care. It covers qualifying system failure and preparation failure on the system we installed. It doesn't cover misuse, impact, chemical damage, excessive heat or standing water. Slab movement and anything outside our control are out too. The full terms are on the About page.
Take a 20 x 20 ft two-car garage. That's 400 sq ft, and in flake it runs about $1,600 to $4,800. Metallic and quartz cost more per foot. We price every job on its own, and the full table is on the garage floor coating page.
At our ranges, 1,000 sq ft works out to about $4,000 to $12,000 in flake. Solid color lands around $7,000 to $10,000. Quartz runs about $12,000 to $15,000 and metallic about $12,000 to $20,000. Polyaspartic runs about $5,600 to $14,500, and polished concrete about $5,000 to $15,000.
The combinations are endless, and we mix new colors too. Our flake comes from the Xtreme Polishing Systems (XPS) In Stock collection, sports-team colors included. See custom epoxy floor colors.
Yes. Metallic runs $12 to $20 a sq ft, and every floor comes out different. See metallic epoxy floors.
Five counties: Hernando, Pasco, Hillsborough, Pinellas and Polk. We're based in Brooksville, in Hernando County.
Get a quote
Tell us about your floor
Five short steps and we have what we need to call you back. Or call us now.
Step 1 of 5
Goes straight to us. We never sell your details.
What happens next
01You answer five short questions.
02We call you back as soon as we can.
03We come out to look at the slab and price your floor.
